FirmWare Developer

Hi, usually I use System Workbench (SW4) as IDE, gcc-Arm-none-eabi as compiller, and STM32CUBEMX as project Generator. I have use STM32 since 2012 and have familiar with most of it's peripheral like EXTI,TIMER,ADC,DAC,DMA,SPI,I2C,FSMC, and many more. I have use STM32 for various kind of project from Hobbyst, Robotic, Industrial, And Military application. I know both firmware and Hardware stuff. so, if you are looking for STM32 expert, you come to right person. Let's discuss the detail over the chat. I'm waiting for your reply. Best Regards, Rijal

Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.

It would be great pleasure to work on your job. I have been working full time on STM32F4 series MCU with FreeRTOS. Can deliver the job quickly too as I can reuse some of my codes already developed and tested during last 2-3 years. Please share more details about the product that you are going to develop. I will use GCC for all the development cycle. Thanks for your time and I look forward to hear from you. Regards... Roy

Hello, I have a good expirience with STM32. More than 10 years. Including USB, CAN, Ethernet, camera, BT and WiFi. I have many development boards and tools. Best regards, Vyacheslav.

Good day, I have a lot of experience in firmware development on the STM32 and other arm-based family of microcontrollers. Please contact me so that we can discuss the details of your job.

Hi. I'm professional programmer with experience over 20 years and I very well know STM32 MCUs. What IDE do you want to use? We can discuss this and another questions in the chat. Regards, Alex.

Our team has more then 10 years of experience of development of electronic devices (hardware-software production). We are assure that we can develop a prototype of non contact voltage testers according to a tasks and purposes in a fixed terms.

Hello, i am experienced embedded developer. I have experinece programming various ARM-based chips from Cortex-M0 to Cortex-A72. I will glad to work with you. Thanks.

I am Excellent at the following: - Embedded C Programming. - STM32F407VG DISCOVERY BOARD. - STM32F4DIS-BB expansion (ethernet+Sdcard +LCD+..). - STM32CubeMX HAL Integgrator - FreeRTOS. - Ethernet RAW API. - STM32 BSP (Board support packages) Integration for audio codec and etc. I can deliver your Target Efficiently at a time. Please check my portfolio, reviews and ratings. If you choose me, I think you won't regret. Best Regards,

Dear sir I have 5+ years experience in device design and firmware programming. I read your project description. I have done similar project already. If you are interested in working with me, please let me know and we can discuss the project more detail. thanks

Hi, I am an embedded developer working in IOT industry. I have worked on smart-metering and smart-lighting solutions. One such was a water meter that used LoRaWAN for communication. This was developed on ultra low-power STM32L072CZ. I created board support package for the controller and then wrote the entire application to record pulses from interrupts, store pulse-count in eeprom, send data over lorawan, and put device to sleep between interrupts. Also the I stored counts on eeprom such that it optimised write-erase cycles. Alternatively, I have worked on projects with PIC and TI controllers. I am proficient in C and algorithms and have very good working experience with UART, SPI, I2C, ADC drivers. So, I am more than capable to work on this. Please, message me and we can discuss the project. Regards, Adarsh

I had industrial experience in STM32 Microcontroller and Cube Tool.

Hi! I understand the requirement. Also, I have experience in firmware development so, let's discuss in detail. Please feel free to contact.

Hello! Experienced in STM32F151, STM32F405 MCUs firmware development. Have already adopted RTOS and library of subprograms. We work in automotive and industrial areas.

I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. I have experience in openCV library for image/video processing. I have ex

Hello, I have 3 years of experience on MCU's. I have been working on STM32F407 to develop Autopilot for about 1 year. I would like to hear details. Best Regards, Mert KUŞ

i currently working with STM32, and did alot of project on it. For example, a Air Conditional central controller for office in AUS, a STM32 and 320x320 LCD for washing machine from Korea. I confidently be a good candidate for this position. Let talk with me for further co-operation.