Find Jobs
Hire Freelancers

I need a loader to read write external memory st 45pe16vg using JTAG to connect through arm stm32f405

£10-15 GBP / hour

Cerrado
Publicado hace alrededor de 5 años

£10-15 GBP / hour

I need a loader to read write external memory st 45pe16vg using JTAG to connect through arm stm32f405 I connect via jtag to stm32f405 using st-link software but there is no current loader in the list for external memory chip Micron 45pe16 that I want to read and write. Instructions say that a custom loader needs to be written. I am not a programmer so would like to hire this job out.
ID del proyecto: 18571893

Información sobre el proyecto

5 propuestas
Proyecto remoto
Activo hace 5 años

¿Buscas ganar dinero?

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto
Cobra por tu trabajo
Describe tu propuesta
Es gratis registrarse y presentar ofertas en los trabajos
5 freelancers están ofertando un promedio de £14 GBP /hora por este trabajo
Avatar del usuario
Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.
£16 GBP en 20 días
4,9 (52 comentarios)
6,6
6,6
Avatar del usuario
Hi there. I offer you the services for ARM designs, I complete the jobs in STM32F4**. I am new on freelancer site, but I am ARM design expert with 10+ years of experience in Circuit designs, PCB designs, ARM software development. You can check our designs in our portfolio. If you want, I will share more designs I completed so far through interview. So I like to discuss the job with you. Lets talk about your project through interview. Thank you.
£15 GBP en 40 días
5,0 (7 comentarios)
4,6
4,6
Avatar del usuario
Hi. Thanks for your posting. I am an electronic engineer, having enough experience in IOT device, high speed circuit & PCB design. I am sure I can support you with my skills. Following is my skills and tools - Electrical & electronic diagram, and schematic & PCB design. • High circuit analysis and design such as DDR3, eMMC, 10Gbps Ethernet circuit • RF Antenna/Front end, filter. • Flexible PCB inlay design. design(Up to 12 layers PCB design). - Standardization and protocols • FCC, ISO/IEC 14443, ISO/IEC 18092, ISO 18000 • ISO IEC 7816, ISO/IEC 7815 - Firmware development for any MCU. • ARM Cortex Mxx, STM32xx, ATSAME70, AT91SAM, STC. • AVR: ATmega328, ATmega1280, ATmega2560, ATtiny43U, ATtiny85... • PIC: PIC16, 18, 24, 32 series • Raspberry Pi • Arduino series: arduino Uno, Mega2560 • Standalone RF module such as Nordic series, WiFi(ESP32, ESP8266) , BLE, Zigbee, Xbee Design Tools - Altium Designer 18, Cadsoft Eagle PADs, OrCAD - MPLAB X, Micro C, uKeil, STM32 workbench, AVR Studio. Arduino IDE - C, C++. I can give you a perfect project. Best Regards.
£13 GBP en 40 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hey, I'm Victor, i've been a hardware and software developer for 6+ years. I've worked with some of the biggest tech initiatives in innovation including Harmony hub, ITESL labs, google and others. I specialize in building hardware and software solutions for home automation and security, IoT, Drone technology, survey devices etc. I built the AI security cam for Harmony hub which increases the efficiency of logging workers into the building, i also developed the falcon med drone for ITESL fablabs which tripled their revenue in the first few months and continues to grow each month.
£13 GBP en 40 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
1) Embedded Firmware Engineer with 12+ years of experience in System Architecture Design, Embedded Firmware Development with Hardware background, Low-level driver development, debugging skills in non-RTOS based systems. 2) FreeRTOS on STM32F4x (ARM Cortex M4) Platforms. 3) Six Sigma Green Belt certified & have two patents against my name.
£15 GBP en 30 días
0,0 (0 comentarios)
0,0
0,0

Sobre este cliente

Bandera de UNITED KINGDOM
Consett, United Kingdom
0,0
0
Miembro desde ene 21, 2019

Verificación del cliente

¡Gracias! Te hemos enviado un enlace para reclamar tu crédito gratuito.
Algo salió mal al enviar tu correo electrónico. Por favor, intenta de nuevo.
Usuarios registrados Total de empleos publicados
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Cargando visualización previa
Permiso concedido para Geolocalización.
Tu sesión de acceso ha expirado y has sido desconectado. Por favor, inica sesión nuevamente.