Publica un proyecto

EXPLORAR

Electrical Engineering

Microcontroller

4,2

(1 comentario)

Foto de portada de perfil

Mithun Kumar D.

@Mithun2li

4,2

1

0,0

0,0

100%

Circuit Design, PCB, MCU Prog, R&D etc.

$25 USD / hora

・

Bangladesh (1:17 p. m.)

・

Se unió el julio 31, 2010

・

1 Recomendación

$25 USD / hora

・

B. Sc. in EEE. Experience: 10yrs + R&D. My services_ _ Research and Development with Electronics Circuits _ Circuit and PCB Design with manufacturing _ Micro-controller programming (PIC/dsPIC, Arduino/AVR) _ Complete Product design (Electrical and Electronics Circuit based) My lab: M's Lab Engineering Solution Expert in_ - MikcoC pro, Arduino - Sprint Layout, Altium, DipTrace - Proteus ISIS - Power Electronics - Embedded Systems - Analog Electronics - Digital Electronics - Micro-controllers - Renewable Energy - Control circuits - PLC

Verificaciones

Aceptar tarifa

100 %

Ver todo Electronics Engineers en Bangladesh

Portafolio

Portafolio

This is a PID trainer kit with facilities listed below:
List of features:
• Temperature sensor PT100 interface
• CDS rotational IR sensor interface
• F/V converter with Offset and Gain Control
• Photo sensor interface
• ON/OFF control
• Comparator with hysteresis
• PID control
• V/PWM converter
• +/- 10V supply source
• AC220V power supply

PID Trainer kit

This is a biomedical and IoT trainer kit. Features are listed below
> ECG sensor interface
> Heart rate sensor interface
> SOP2 sensor interface
> Pulse sensor interface
> DHT11 interface
> ds18b20 interface
> Blood pressure measurement facilities
> Arduino Mega on board with I/O filters and resistors sents
> OLED and LCD display interface
> User buttons and variables
> ESP8266 socket
> On board voltmeter with buck converter
> USB and external power supply facilities
> Onboard 5V & 3.3V supply
> Buzzer, LEDs etc

Biomedical and IoT trainer kit

Disinfectant Tunnel controller for COVID-19 issue.
Operates from both AC and DC sources. Storage Battery with charging feature.
IR transmitter and Receiver at 38KHz.

Disinfectant Tunnel controller for COVID-19 issue.

This is a 8051 trainer kit. Supports MCU: AT89S52.
Features:
• MCU: 8051 series. AT89S52
• LCD 16X2 display
• GLCD 128X64 display
• RTC module:DS1307
• Seven Segment display, Common Anode & Common Cathode
• 8 LEDs
• 2 RGB LEDs
• DC power: 12V
• Dot Matrix display
• Serial Communication, DB9 + MAX232
• 4 user buttons and 3 user variables with GND bypass
• 3 Relays
• Audio buzzer
• Mini project board
• 5V power supply
• 4X4 matrix keypad
• Crystal oscillator base
• USBasp programmer with bypass switch
• Reset switch
• Pull up and pull-down options
• Selectable I/O through DIP switches
• Selectable Vpp.

8051 Trainer kit

This is a 8051 trainer kit. Supports MCU: AT89S52.
Features:
• MCU: 8051 series. AT89S52
• LCD 16X2 display
• GLCD 128X64 display
• RTC module:DS1307
• Seven Segment display, Common Anode & Common Cathode
• 8 LEDs
• 2 RGB LEDs
• DC power: 12V
• Dot Matrix display
• Serial Communication, DB9 + MAX232
• 4 user buttons and 3 user variables with GND bypass
• 3 Relays
• Audio buzzer
• Mini project board
• 5V power supply
• 4X4 matrix keypad
• Crystal oscillator base
• USBasp programmer with bypass switch
• Reset switch
• Pull up and pull-down options
• Selectable I/O through DIP switches
• Selectable Vpp.

8051 Trainer kit

This is an Arduino Development board designed by me and supplied to educational institutes.

Arduino Development board

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

This is a PID trainer kit with facilities listed below:
List of features:
• Temperature sensor PT100 interface
• CDS rotational IR sensor interface
• F/V converter with Offset and Gain Control
• Photo sensor interface
• ON/OFF control
• Comparator with hysteresis
• PID control
• V/PWM converter
• +/- 10V supply source
• AC220V power supply

PID Trainer kit

This is a biomedical and IoT trainer kit. Features are listed below
> ECG sensor interface
> Heart rate sensor interface
> SOP2 sensor interface
> Pulse sensor interface
> DHT11 interface
> ds18b20 interface
> Blood pressure measurement facilities
> Arduino Mega on board with I/O filters and resistors sents
> OLED and LCD display interface
> User buttons and variables
> ESP8266 socket
> On board voltmeter with buck converter
> USB and external power supply facilities
> Onboard 5V & 3.3V supply
> Buzzer, LEDs etc

Biomedical and IoT trainer kit

Disinfectant Tunnel controller for COVID-19 issue.
Operates from both AC and DC sources. Storage Battery with charging feature.
IR transmitter and Receiver at 38KHz.

Disinfectant Tunnel controller for COVID-19 issue.

This is a 8051 trainer kit. Supports MCU: AT89S52.
Features:
• MCU: 8051 series. AT89S52
• LCD 16X2 display
• GLCD 128X64 display
• RTC module:DS1307
• Seven Segment display, Common Anode & Common Cathode
• 8 LEDs
• 2 RGB LEDs
• DC power: 12V
• Dot Matrix display
• Serial Communication, DB9 + MAX232
• 4 user buttons and 3 user variables with GND bypass
• 3 Relays
• Audio buzzer
• Mini project board
• 5V power supply
• 4X4 matrix keypad
• Crystal oscillator base
• USBasp programmer with bypass switch
• Reset switch
• Pull up and pull-down options
• Selectable I/O through DIP switches
• Selectable Vpp.

8051 Trainer kit

This is a 8051 trainer kit. Supports MCU: AT89S52.
Features:
• MCU: 8051 series. AT89S52
• LCD 16X2 display
• GLCD 128X64 display
• RTC module:DS1307
• Seven Segment display, Common Anode & Common Cathode
• 8 LEDs
• 2 RGB LEDs
• DC power: 12V
• Dot Matrix display
• Serial Communication, DB9 + MAX232
• 4 user buttons and 3 user variables with GND bypass
• 3 Relays
• Audio buzzer
• Mini project board
• 5V power supply
• 4X4 matrix keypad
• Crystal oscillator base
• USBasp programmer with bypass switch
• Reset switch
• Pull up and pull-down options
• Selectable I/O through DIP switches
• Selectable Vpp.

8051 Trainer kit

This is an Arduino Development board designed by me and supplied to educational institutes.

Arduino Development board

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

This is a smart wheel chair which can monitor the patient's blood pressure, heart rate, ecg signal and body temperature. which is logged in the website(thingspeak) periodically. Any abnormal condition will send a SMS to predefined number.

The wheel chair is capable of taking load up to 120Kg human except its own load. Wheel chair is operated with two ways, either flex sensor or joystick can be used to control its movement. When going backward, an obstacle sensor monitors clearance in back side and warns if required. Smooth movement makes the wheel chair user friendly.

IoT based wheel chair with patient monitoring system

4.2 · 1 Comentario

Opiniones

S

Operating Servo, temperature thermocouple and DC brushed motor via Arduino • $15 AUD

Supportive

Microcontroller

Electrical Engineering

Sultan A.

@sulking1988

•

Coolbellup, Oman

•

hace 8 años

Compartir

System designer & Entrepreneur

feb, 2012 - Presente

•

14 años

M's Lab Engineering Solution

feb, 2012 - Presente

•

14 años

Its my own electronics laboratory and I've been working here, doing researches, making new systems, new circuits. I'm proud to be an Entrepreneur.

feb, 2012 - Presente

•

14 años

Khulna University of Engineering and Technology

2007 - 2011

•

4 años

B. Sc in EEE

Bangladesh

2007 - 2011

•

4 años

B. Sc. Engineer

2011

Khulna University of Engineering and Technology

B. Sc. in Electrical and Electronic Engineering degree certificate.

2011

P

Preferred Freelancer Program SLA

Analog Electronics